Many thanks Neil, i am seriously considering it.
Regards
Sven
Search found 80 matches
- Thu Aug 10, 2023 9:38 pm
- Forum: GENERAL CHAT
- Topic: Spinning
- Replies: 17
- Views: 15151
- Thu Aug 10, 2023 9:38 pm
- Forum: GENERAL CHAT
- Topic: Spinning
- Replies: 17
- Views: 15151
Re: Spinning
Many thanks Neil, i am seriously considering it.
Regards
Sven
Regards
Sven
- Tue Aug 08, 2023 8:33 pm
- Forum: GENERAL CHAT
- Topic: Spinning
- Replies: 17
- Views: 15151
Re: Spinning
Dear Neil, Thank you for the response. I shall try it gently and report back. I am slowly developing the negative g side - with "straight" rolls and then i will try more extended inverted flight. So far no splutter or other trouble from the motor. What is the nature of the work you did to ...
- Tue Aug 08, 2023 9:11 am
- Forum: GENERAL CHAT
- Topic: Spinning
- Replies: 17
- Views: 15151
Re: Spinning
Pat wrote "Do try this one thouigh: throttle back to about 1600 rpm and ease the speed back to about 60 mph and then simutaiously apply full rudder and aft stick But do it GENTLY. Result instant gentle flick roll....Huge fun. " UDT has a full flying rudder - would it be advisable / possibl...
- Tue Aug 08, 2023 9:04 am
- Forum: ENGINEERING AND MAINTENANCE
- Topic: engine temperatures
- Replies: 11
- Views: 2218
Re: engine temperatures
My oil temps vary bwteen 70 to 81 (mostly around 78)
CHT around 110 (measured at the rear cylinders)
EGT around 580 to 640 (measured at the rear cylinders)
Hope this helps
Sven UDT
CHT around 110 (measured at the rear cylinders)
EGT around 580 to 640 (measured at the rear cylinders)
Hope this helps
Sven UDT
- Fri Jun 09, 2023 1:35 pm
- Forum: THE PILOTS
- Topic: ZS-UDT
- Replies: 2
- Views: 15431
Re: ZS-UDT
and she is such a pleasure to fly
- Tue Apr 04, 2023 2:39 pm
- Forum: PHOTOGRAPHS
- Topic: An upside down world - 1 April 2023
- Replies: 0
- Views: 16011
- Thu Sep 01, 2022 2:23 pm
- Forum: GENERAL CHAT
- Topic: Hand swinging a Nipper
- Replies: 7
- Views: 4536
Re: Hand swinging a Nipper
I swing the prop standing in front of the wing and behind the prop - so i can reach both the throttle and the ignition. I have a second behind the wing with fingers on the ignition should i shout "CUT". Otherwise i very much follow Ms Bumble Bee's technique. I prime using the electric pump...
- Mon Aug 29, 2022 5:19 pm
- Forum: PHOTOGRAPHS
- Topic: ZS-UDT double camera
- Replies: 2
- Views: 2881
ZS-UDT double camera
UDT is back in the skies after a wait to replace the UC bungees (thanks LAS).
https://youtu.be/DU0TZoavPO8
https://youtu.be/DU0TZoavPO8
- Sun May 15, 2022 8:17 pm
- Forum: PHOTOGRAPHS
- Topic: fully inverted
- Replies: 0
- Views: 16749
fully inverted
first fully inverted flight in UDT - two slow rolls
- Fri May 06, 2022 1:16 pm
- Forum: GENERAL CHAT
- Topic: Eddsfield
- Replies: 1
- Views: 3529
Re: Eddsfield
Lovely
- Mon Apr 11, 2022 3:32 pm
- Forum: PHOTOGRAPHS
- Topic: Sunset ZS-UDT
- Replies: 3
- Views: 5870
- Wed Feb 16, 2022 11:12 am
- Forum: PHOTOGRAPHS
- Topic: Sunset ZS-UDT
- Replies: 3
- Views: 5870
Sunset ZS-UDT
Busy with testing all the systems - so only taxi tests and short hops at the moment
- Sun Feb 06, 2022 7:11 pm
- Forum: ENGINEERING AND MAINTENANCE
- Topic: New engine
- Replies: 55
- Views: 33176
Re: New engine
Good to go - I hope - fingers crossed
- Fri Nov 12, 2021 5:44 am
- Forum: ENGINEERING AND MAINTENANCE
- Topic: New engine
- Replies: 55
- Views: 33176
Re: New engine
Fuel tank mods done
Cowling mods nearly finished
will now see if i can get the engine running with the new carb
Hope to see it in the air this weekend
Cowling mods nearly finished
will now see if i can get the engine running with the new carb
Hope to see it in the air this weekend